WireGuard Ops

wg-quick compatiable config generator with additional features supported.

Basic Usage

1. Clone this repo with git clone https://github.com/Kiritow/wg-ops

2. Run install.sh. (May prompt sudo)

3. Write a valid WireGuard wg-quick config file, with supported extension tags. (see below)

4. Run python3 generate.py to convert extension tags into config lines.

5. Bring it up with wg-quick up

Start as service: systemctl start wg-quick@wg0

Start service on system start-up: systemctl enable wg-quick@wg0

See wg-quick(8) for more information.

Options

python3 generate.py [-h] [-k] [-o filename] source_filename

-h Display this help and quit.

-k Output generated config to standard output

-o filename Output generated config to filename. Default write to source_filename.gen

Generic Tags

enable-bbr

Enable TCP BBR. Most of the time it's useful on VPS.

enable-forward

Set net.ipv4.ip_forward to 1. Enable ip packet forward.

enable-dns-reload

Enable DNS reloader for peers with endpoint. For each peer, a transient timer and service will be created and try resolving endpoint domain name every 30 seconds. If the dns record of a domain changes, wg-ops will try to update wireguard interface endpoint settings live.

iptables-forward

Add iptables rules to accept forward from this wireguard interface. Example: iptables -A FORWARD -i wg0 -j ACCEPT

iptables-gateway

Add iptables rules to masquerade source ip as a gateway. Example: iptables -t nat -A POSTROUTING -o wg0 -j MASQUERADE

podman-user username

Run podman container as username. Default to root.

Tunnel Tags

udp2raw-server name port password

Setup a udp2raw server. Raw mode set to fake-tcp. Expose & listen on port port.

udp2raw-client name port remote password

Setup a udp2raw client. Listen on port port.

udp2raw-client-mux name mux_size port remote password

Setup multiple (up to mux_size) udp2raw clients. Listen on ports from port to port + mux_size

gost-server name port

Setup a gost server. Forward mode set to relay+tls. Expose & listen on port port.

gost-client name port remote

Setup a gost client. Listen on port port.

gost-client-mux name mux_size port remote

Setup multiple (up to mux_size) gost clients. Listen on ports from port to port + mux_size

trojan-server name port password cert_path key_path

Setup a trojan-go server. Expose & listen on port port.

Requires a ssl certificate signed by trusted CA.

acme.sh is recommended for acquiring ssl certs. Make sure use fullchain.cer as cert_path

trojan-client name port password remote_host target_port

Setup a trojan-go client. Listen on port port.

trojan-client-mux name mux_size port password remote_host target_port

Setup multiple (up to mux_size) trojan-go clients. Listen on ports from port to port + mux_size

Peer Tags

use-tunnel name

Use tunnel name for this peer. wg-ops may add Endpoint= or use wg set peer to fullfill this requirement.

Route Tags

route-to ip_route_table

Used in chained WireGuard settings. Accept any traffic from ip_route_table.

Interface marked with route-to should have only one peer.

route-from ip_route_table

Used in chained WireGuard settings. Route traffic from all peers or a marked peer with ip_route_table.

Example: The following config means all traffic from 10.44.0.2 will be forward to 10.33.0.1

wg0.conf (Should have only one peer)

[Interface]
Address=10.33.0.2
#route-to TABLE

[Peer]
AllowedIPs=10.33.0.1

wg1.conf

[Interface]
Address=10.44.0.1

[Peer]
AllowedIPs=10.44.0.2
#route-from TABLE

Notice

Make sure to setup firewall for better security. ufw is recommended for Ubuntu.